Lian Chun Ltd.

News updates

  2. Info
  3. News updates

  1. Heat dissipation:
    High-speed data transmission and processing may generate heat. If the temperature is too high, the performance of the M.2 SSD may be affected. By adding heat dissipation fins, you can increase the surface area and provide more surfaces for heat dissipation, thereby effectively reducing the operating temperature of the SSD.
  2. Extended usage time:
    Operating at higher temperatures may accelerate the aging and wear of components, thereby reducing the life of the SSD. Thermal fins help maintain lower operating temperatures, extending the life of your SSD.
  3. Stability:
    Some M.2 SSDs may experience performance variability or hot node phenomena under high load conditions. By adding cooling fins, you can help disperse heat evenly, improve overall stability, and reduce the risk of performance degradation or other issues.
  4. It is worth noting that not all M.2 SSDs require cooling fins. This depends on the specific SSD model, use case, and manufacturer's design choices. Some SSDs may use other cooling technologies, such as heat pipes or heat sinks. Thermal fins may not be necessary for lower power SSDs or use scenarios with lower cooling requirements. The best practice is to refer to the SSD manufacturer's recommendations and guidelines to determine if additional thermal solutions are required and select appropriate thermal fins or other cooling measures if needed.

  1. High frequency and fast transmission speed:
    Gaming DDR modules usually have higher clock frequency and fast data transmission speed. This allows them to provide faster data access speeds, reduce latency, provide a smoother gaming experience and higher computing performance.
  2. Low latency:
    Gaming DDR usually has low CAS latency (Column Address Strobe Latency), which is the time required to read data from the memory module. Low latency helps improve the fast reading and writing of data and increases the response speed of the system.
  3. High Capacity:
    Gaming DDR modules offer high-capacity memory options to meet the memory requirements required to handle large-scale games and multi-tasking applications. This helps games and applications process more data simultaneously, providing smoother gaming graphics and higher performance.
  4. Overclocking capability:
    Gaming DDR modules usually have good overclocking capabilities, meaning they can run at high frequencies beyond their settings. This allows users to further improve memory performance by adjusting clock frequency and timing for higher game frame rates and faster system response.
  5. The application fields of Gaming DDR are mainly concentrated in games, high-performance gaming computers and workstations. They offer high-performance, low-latency, and high-capacity memory options that help deliver a great gaming experience, fast data processing, and smooth multitasking. Gaming DDR is an ideal memory choice for users who need to handle graphics-heavy, compute-intensive games or multi-threaded workloads.

  1. Liquid Cooling Systems:
    Liquid cooling systems use liquid cooling devices, such as cooling blocks or cooling tubes, to transfer heat from electronic devices into a coolant. This system has higher heat dissipation efficiency and heat dissipation capacity, and can effectively reduce the temperature of the device. Liquid cooling systems are commonly used in high-performance computers, game consoles, and high-performance servers.
  2. Heat pipe cooling technology:
    Heat pipe is an efficient heat conduction device, often used in radiators and heat sinks. Heat pipes use the thermal conductivity properties of liquid or gas to transfer heat from the heat source to the radiator to achieve rapid and effective heat dissipation. In recent years, heat pipe technology has been continuously improved and applied to meet the cooling needs of high-power and high-density electronic equipment.
  3. Phase change material heat dissipation technology:
    Phase change material is a material with special heat storage and release capabilities, which can absorb or release a large amount of heat during the phase change process. This material can be used in the heat dissipation system of electronic equipment to absorb and store the heat generated by the equipment, and release the heat when the temperature exceeds a certain range, thus stabilizing the temperature of the equipment.
  4. Nano material heat dissipation technology:
    Nano materials have unique physical and chemical properties and can be used in electronic heat dissipation. For example, nanomaterials such as carbon nanotubes and graphene have excellent thermal conductivity properties and can be used to create efficient heat dissipation materials and heat dissipation systems. In addition, nanomaterials can also be used in thermal interface materials and thermal paste to improve heat dissipation efficiency.

  1. The pressure expansion coefficient of thermal conductive strips is usually expressed as "compression modulus" or "compression coefficient" to measure the degree of compression deformation of the material when it is subjected to pressure. The unit of compression modulus is Pascal or Megapascal.
  2. The specific pressure expansion coefficient depends on the material composition and characteristics of the thermal conductive strip. Different thermal strips may have different compression modulus. Generally speaking, the greater the compression modulus of a thermal conductive strip, the less it deforms when subjected to pressure.
  3. When selecting thermal strips, it is often necessary to consider the material's compression modulus to ensure correct pressure and contact properties for the application. An appropriate pressure expansion coefficient can ensure that the thermal conductive strip can effectively fill the gap between the thermal interfaces during installation and provide good thermal conductivity.
  4. It is important to note that the pressure expansion coefficient of each type of thermal conductive strip may vary, so when selecting and applying, it is recommended to refer to the material specifications and technical information provided by the manufacturer to ensure optimal performance and reliability sex.

  1. The pressure expansion coefficient is an elastic property of a material that describes the degree of deformation of the material when it is subjected to pressure. It is the proportional relationship between stress and strain in a material.
  2. A common material testing method is the compression test, in which pressure is applied to the material and the corresponding strain is measured to calculate the pressure expansion coefficient. These tests can be performed in a laboratory or in specialized materials testing equipment.
  3. The pressure expansion coefficient is usually expressed as compressive modulus, which is defined as the ratio of stress to strain of a material under pressure. The unit of measurement for compression modulus is Pascal or Megapascal.
  4. Since different thermal strip materials may have different compression modulus, when selecting thermal strips, it is recommended to refer to the material specifications and technical information provided by the supplier to determine its compression modulus and related properties. This information is typically provided by material manufacturers to assist customers in selecting appropriate materials and applications.

  1. Transfer speed:
    M.2 SSD with PCIe interface has higher transfer speed. The PCIe 3.0 x4 interface can provide higher bandwidth and speed, resulting in faster data reading and writing speeds. In comparison, the transfer speed of M.2 SSD with SATA interface is lower and is limited by SATA III 6Gbps.
  2. Performance:
    Because the PCIe interface provides higher bandwidth, PCIe M.2 SSDs generally have better performance. They enable faster boot times, shorter data read times, and higher file transfer speeds. For applications that need to handle large files, run multitasking, or require high-performance computing, M.2 SSDs with PCIe interface are a better choice.
  3. Compatibility:
    Most modern motherboards support M.2 slots, but pay attention to compatibility. Some motherboards only support SATA M.2 SSD but not PCIe M.2 SSD. Therefore, when choosing an M.2 SSD, make sure the motherboard and interface are compatible.
  4. Cost:
    Generally speaking, M.2 SSD with SATA interface is relatively cheaper, while M.2 SSD with PCIe interface is more expensive. This is due to the fact that the PCIe interface offers higher performance and speed and is therefore relatively more expensive.
  5. In general, if you are pursuing higher speed and performance, and your system supports the PCIe interface, then PCIe M.2 SSD is a better choice. If your system only supports SATA interface or your speed and performance requirements are not very high, then SATA M.2 SSD can meet general storage needs.

  1. Highly demanding applications:
    Many industrial applications have high requirements for computing power and processing speed. For example, in automated manufacturing systems, industrial computers need to process large amounts of data and control signals to ensure precise and efficient operations. Insufficient performance can lead to production delays or quality issues.
  2. Multi-tasking:
    Computers in industrial environments usually need to handle multiple tasks at the same time, such as monitoring systems, data collection, data analysis, control operations, etc. These tasks require efficient processors and memory to ensure stability and smoothness when executing multiple tasks simultaneously.
  3. Durability and Reliability:
    Industrial environments are often harsh, including high and low temperatures, vibration, dust, moisture, etc. Industrial computers need to have the durability and reliability to operate stably for long periods of time under these harsh conditions. High-performance hardware components and optimized cooling systems provide better reliability and stability.
  4. Data processing and instant feedback:
    In some industrial applications, instant feedback is crucial. For example, in intelligent transportation systems, industrial computers need to instantly process and analyze data from traffic surveillance cameras to quickly make traffic control decisions. High-performance processors can speed up data processing and provide faster response times.
  5. In summary, industrial computers require higher and more stable performance in order to cope with complex industrial environments, multi-tasking requirements, instant feedback requirements and to ensure long-term reliable operation. These features improve production efficiency, quality control and safety while ensuring stable operation of industrial systems.

Contact with Us

If you have any questions about product specifications, selling prices, etc., or have any comments or suggestions, please feel free to contact us immediately。